There is no such thing as a standard printed circuit board. Each PCB has a unique function for a particular product. Therefore, producing a PCB is a complex process of many steps. This overview covers the most important steps when producing a multilayer PCB.

When you order PCBs from the AllWinPcba, you are buying quality that pays for itself over time. This is guaranteed through a product specification and quality control that is far more stringent than other suppliers, and ensures that the product delivers what it promises. In the production flow below you can see where the AllWinPcba process is unique or goes beyond the IPC standard.

Step 1. Front-end tool data preparation --- DFM

The PCB designer has prepared his layout on a Computer Aided Design or CAD system.Each CAD system uses its own internal data format, so the PCB industry has developed a standard output format to transfer the layout data to the manufacturer. This is Extended Gerber or RS274X. The Gerber files define the copper tracking layers as well as the solder masks and component notations. First we check that data meets our manufacturing requirements. We check the track widths, the space between tracks, the pads around the holes, the smallest hole size etc. The engineer can also check and measure individual areas where he wishes. That's called a Design for Manufacture (DFM) check. Once the data is verified as good he will output all the tool files needed to drive the machines that will make and test the PCB.

Step 2. Preparing the phototools for PCB image transfer

We use laser photoplotters in a temperature and humidity-controlled darkroom to make the films we will use later to image the PCBs. The photoplotter takes the board data and converts it into a pixel image. A laser writes this onto the film. The exposed film is automatically developed and unloaded for the operator. The films are ready now for the PCB fabrication process.

Step 3. Material Preparation

The copper-clad panels along with the drill entry material & a back-up-board are cut to size for down stream process. The standard panel is an epoxy resin and glass-fibre core with copper foil pre-bonded onto each side.

Step 4. Innerlayer imaging for multilayer PCB

To produce the inner layers of our multilayer PCB, we start with a panel of laminate. Panels are coated by double films and then exposed to a high intensity ultraviolet light source coming. Clear areas allow light to pass through and polymerize (harden) the film resist thus creating an image of the circuit pattern –similar to a negative and a photograph.Then the copper is chemically removed from the core in all areas not covered by the dry-film resist. This creates the copper pattern that matches the film pattern.The core laminate surface is exposed in areas where copper was etched away.

Step 5. Etching inner layer in multilayer PCB production

We remove the unwanted copper using a powerful alkaline solution to dissolve (or etch away) the exposed copper from the inner layer. The process is carefully controlled to ensure that the finished conductor widths are exactly as designed. But designers should be aware that thicker copper foils need wider spaces between the tracks. The operator checks carefully that all the unwanted copper has been etched away.

Step 6. Register punch and Automatic Optical Inspection (AOI) of inner layers

The inner core of our multilayer is now complete. Next we punch the registration holes we will use to align the inner layers to the outer layers. The operator loads the core into the optical punch which lines up the registration targets in the copper pattern and punches the registration holes. We won’t be able to correct any mistakes on the inner layers once we have assembled the multilayer so we now give the panel a complete machine inspection.The automatic optical inspection system scans the board in broad strips and compares it with the digital image generated from the original design data. Any errors are displayed on screen. If allowed and practical, some repairs can be made at this point. Information on defects is shared with the appropriate departments to correct any process problems.

Step 7. Lay-up and bond for multilayer PCB

Inner layer core, copper foil and prepreg are bonded together under heat and pressure, sometimes in a vacuum, during the lamination process. The result is a panel with several layers of copper inside as well as the foil on the outside.

Step 8. Drilling printed circuit boards

Now we drill the holes for leaded components and the via holes that link the copper layers together. First we use an X-ray drill to locate targets in the copper of the inner layers. The machine drills registration holes to ensure that we will drill precisely through the centre of the inner layer pads. Drilled hole sizes are usually 5 mils larger than finished plated through hole sizes to allow for the copper plating process.

Step 9. electroless copper deposition

The first step in the plating process is the chemical deposition of a very thin layer of copper on the hole walls.This creates a metallic base for electroplating copper into the holes and onto the surface.

Step 10. Image the outer layers

The same imaging process used on the inner layers is used for the outer layers.

Step 11. Plating

Next electroplate the boards with 25 microns of copper through the hole and an additional 25 – 30 microns on the tracks and pads, depending on the required final finish for the panel.

Step 12. Etch outer layers

We have now plated the panel with copper that is covered with a thin layer of tin as an etch resist. We will remove the unwanted copper foil from the surface.Then the tin is chemically removed leaving behind a bare copper and laminate panel. The surface pads, traces and plated through holes are the exposed copper.

Step 13. AOI or electrical test of outer layers after etched

Once the outer layers was etched, it's also impossible to correct any errors. An automatic optical inspection(AOI) of the panels to confirm a total absence of defects as same as inner layers AOI. Sometimes a technician performs electrical tests on the PCB with test jig. The automated procedure confirms the functionality of the PCB and its conformity to the original design. Once the layer passes inspection, it moves to the next step. .

Step 14. Apply soldermask

Most boards have a epoxy-ink soldermask printed onto each side to protect the copper surface and prevent solder shorting between components during assembly. Surface Coating, Image Transfer, Legend Printing, Final Curing. .

Step 15. Surface finishes

The copper component pads and holes have been left clear of soldermask. Now we apply a solderable surface finish to protect the copper until the components are soldered onto the board.There are a number of processing options that can occur depending upon the desired final finish. Currently at PCBAStore we can provide our customers with a SnPb or lead free solder finish, hard gold, Electroless Nickel Immersion Gold (ENIG), immersion tin or immersion silver. Other finishes include Organic Solderable Preservative (OSP), soft or bondable gold and a number of other “exotic”finishes like palladium..

Step 16. Silk-screen and cure

Most PCBs have a component legend to show which component goes where. Ink is silkscreened onto one or both sides of the panel depending on the requirements of the customer. Today we use ink-jet printers to image the legends direct from the board digital data. Panels are then baked to cure the ink.

Step 17. Profiling

The next stage is to profile the PCBs and cut them out of the production panel to single pieces or arrays of varying sizes. Alternatively we can profile the individual circuits on a V-cut or CNC machine.

Step 18. Bare board Electrical test

We electrically test every PCB whether multilayer or double layer against the original Gerber data. Using a flying probe tester or test jig we check each net to ensure that it is complete (no open circuits) and does not short to any other net. Shorts are repaired when possible and retested for verification.

Step 19. Final Quality Control

In the last step of the manufacturing process a team of sharp-eyed inspectors give each PCB a final careful check-over to assure them meet requirements of our customers, industry specifications (IPC-A-600) and Allwinpcba's standards, as well as having the physical dimensions and hole Sizes verified.

Step 20. Packing & Shipping

Printed Circuit boards meeting the acceptability standards are counted, shrink wrapped and readied for shipment along with all the required certificates, samples, cross sections, etc. They are individually packaged in protective plastic bags for storage or shipping with any methods which depends on the customer's requirements.

Choose AllWinPcba for your PCB Assembly requirement

AllWinPcba provides a one stop solution for all of your electronic manufacturing requirements with our experienced team and state-of-the-art assembly equipments under one roof in an inexpensive way, ranging from fast turnaround prototyping to high volume manufacturing. We have the capability to identify design and production issues during the prototype stage and solve these (in consultation with you) before mass production. Our turnkey or consigned printed circuit board assembly service is ISO ISO9001:2015-certified and RoHS compliant. We handle SMD, through-hole and mixed assembly projects. Look forward to cooperating with you, welcome your inquiry: svc@allwinpcba

PCB Assembly Online Quote